Search results for "melt spinning"
showing 10 items of 14 documents
MULTIFUNCTIONAL FIBERS BASED ON POLYAMIDE 6 AND PLASMA FUNCTIONALIZED CARBON NANOTUBES MoDeSt 2012 Conference, Praga, 2-6 Settembre 2012.
2012
Commercial (CNT 1) and ad hoc synthesized carbon nanotubes (CNT 2) were plasma treated under oxygen atmosphere and then added to polyamide 6 (PA 6) in order to prepare multifunctional fibres by melt spinning. For comparison, pristine nanofillers were used too. The effect of functionalization and of filler characteristics on the morphological, rheological, mechanical and electrical properties of the fibers was studied by TEM and SEM, rheological measurements, tensile tests and electrical conductivity tests. The amalysis of Raman spectra put into evidence that the intensity of D-band (correlated with the degree of functionalization by the different vibration mode of carbon atoms in the presen…
Comportamento di nanocompositi PA6/CNT in flusso elongazionale non isotermo
2012
Si sono preparate fibre a matrice poliammidica caricate con CNT. Sono state utilizzate due diverse tipologie di CNT a differente fattore di forma e grado di purezza, ossidate mediante plasma di ossigeno. Le misure di viscosità elongazionale hanno evidenziato che l’introduzione della carica comporta un incremento della MS a fronte di una diminuzione della BSR per tutti i materiali caricati. La tipologia e la funzionalizzazione dei CNT hanno delle notevoli ricadute sul diverso comportamento reologico. Studi morfologici hanno evidenziato che dopo la funzionalizzazione si registrano livelli di dispersione, allineamento e adesione interfacciale più alti. La natura delle interazioni matrice-caric…
Influence of Drawing on the Antimicrobial and Physical Properties of Chlorhexidine-Compounded Poly(caprolactone) Monofilaments
2015
In this work, we prepared poly(caprolactone) (PCL) monofilaments incorporating different amounts of the antiseptic chlorhexidine diacetate (CHX) and evaluated the effect of “online” drawing during the melt spinning or of an “offline” cold drawing on the antimicrobial and physical properties of PCL/CHX monofilaments. The results showed that the drawing conditions strongly affected the properties of the threads. In particular, the filaments exhibited antimicrobial activity for all the draw ratios (DR) adopted, but on increasing DR the antibacterial efficiency reduced. These results were correlated with the CHX surface concentration and with the release kinetics.
Effect of a Compatibilizer on the Morphology and Properties of Polypropylene/Polyethylentherephthalate Spun Fibers
2017
Fibers spun by melt spinning of binary and ternary polypropylene/ polyethylenetherephthalate blends have been produced and characterized in order to investigate the effect of a compatibilizer on their morphology and mechanical properties. The compatibilizer was a maleic anhydride-functionalized rubber copolymer. The effect of the compatibilizer was well evident in the isotropic state, as the morphology became very fine, the size of the dispersed particles was very small, and the adhesion was better. The effect of the compatibilizer on the mechanical properties is very relevant, especially in the elongation at break. On the contrary, no relevant effect was observed in the anisotropic oriente…
Morphology and Properties of Polyethylene/Clay Nanocomposite Drawn Fibers
2008
The influence of an elongational flow on the morphology of PE/clay nanocomposite drawn fibers was studied. An increase of the elastic modulus and the tensile strength as well as a decrease of the elongation at break are observed with increasing draw ratio. The applied elongational gradient orients the polymer chains and the clay particles along the spinning direction. When the applied flow results in the formation and the orientation of exfoliated nanoparticles, a pronounced increase of the mechanical properties is observed. The dispersed clay particles can be broken and oriented by the extensional flow, which might indicate a flow induced intercalated/exfoliated morphology transition.
Tunable release of Chlorhexidine from Polycaprolactone-based filaments containing graphene nanoplatelets
2019
Abstract Graphene nanoplatelets (GNP) as fillers and Chlorhexidine (CHX), as an antibacterial agent, were incorporated in a polycaprolactone (PCL) matrix and processed into filaments by melt spinning. The influence of both drawing and formulation on the processability, spinnability, mechanical properties and release behaviour of these materials were deeply investigated by performing rheological, morphological analysis, tensile tests, and by measuring the cumulative release of CHX in PBS at 37 °C. Furthermore, Korsmeyer–Peppas model was adopted to study the kinetics release mechanism. The results showed that adding GNP did not alter the processability and spinnability of the systems. Further…
Effect of the nanotube aspect ratio and surface functionalization on the morphology and properties of multiwalled carbon nanotube polyamide-based fib…
2013
In this study, the effect of the carbon nanotube (CNT) aspect ratio and surface functionalization on the mechanical behavior and morphological changes of polyamide (PA)-based fibers was investigated. Composites were prepared by the melt blending of CNTs with PA, and at a later time, the fibers were prepared by melt spinning and cold drawing. A reinforcement effect was noticed for all of the CNTs samples, and the increase in the mechanical properties and dimensional stability was more pronounced for highly oriented filaments. When the elongational flow was increased, the orientation of CNTs along the fiber direction was observed, but the nanotube alignment was much more difficult for CNTs wi…
Processing-property relationships of polypropylene/ciprofloxacin fibers
2015
In this work we prepared polypropylene (PP) fibers incorporating an antibiotic, i.e. ciprofloxacin (CFX), by melt spinning. In particular, PP has been compounded with CFX at different concentrations by using a counter-rotating twin screw compounder. The PP/CFX fibers have been spun by using a capillary rheometer operating under a constant extrusion speed. The effect of “online” hot drawing during the melt spinning or of an “offline” cold drawing on the properties of PP/CFX fibers were evaluated. In particular, the influence of the drawing conditions on the mechanical properties and the release kinetics were studied. Moreover, the rheological behavior in non-isothermal elongation flow has be…
High performance PA6/CNTs nanohybrid fibers prepared in the melt
2012
Commercial and home-made carbon nanotubes (CNTs) were plasma treated under oxygen atmosphere and then added to polyamide 6 (PA6) in order to prepare fibres by melt spinning. For comparison, pristine nanofillers were used too. The effect of functionalization and of filler characteristics on the morphological, rheological, mechanical and electrical properties of the fibres was studied by TEM and SEM, rheological measurements, tensile and electrical conductivity tests. The results demonstrated that the functionalization led to a better mechanical performance and the morphological analysis confirmed that the adhesion, the dispersion and the alignment of the nanotubes within the polymer matrix w…
Melt spinning and mechanical properties of semirigid liquid-crystal copolyesters
1993
Melt-spinning and mechanical properties of fibers of a new class of semirigid thermotropic liquid-crystal polymers are presented. These copolyesters are synthesized from 4-4′-dihydroxybiphenyl (B), 4-hydroxybenzoic acid (H), and flexible units provided by aliphatic diacids. The flexible units depress the melting temperature without strongly depressing the mechanical properties. These liquid-crystal polymers can be easily spun at high draw ratios. Indeed, unlike rigid liquid-crystal polymers, relatively high draw ratios are needed to attain high mechanical strength. Tensile moduli of about 28 GPa and tensile strengths of about 350 MPa are obtained. © 1993 John Wiley & Sons, Inc.